Salta la navigazione

Schemi del processo produttivo

Il processo produttivo Pyramid™ Renishaw trasforma tecnologie innovative, metodi affidabili ed esperienza consolidata in strumenti capaci di identificare e controllare le variazioni all'interno della fabbrica.

Schemi del processo produttivo

  • (AP010) Productive Process Pattern: Productive Process Patterns™ (AP010) Productive Process Pattern: Productive Process Patterns™ [en]

    Introduction to the Productive Process Patterns™ - solutions for intelligent process control within manufacturing

    [598kB]
  • (AP100) Machine condition monitoring - linear axes (AP100) Machine condition monitoring - linear axes [en]

    When machining a component using a CNC machine tool, the quality of the finished part, for example surface finish and adherence to tolerance, is highly dependent on the positioning and contouring performance of the machine. To maintain machine performance, use a telescoping ballbar to conduct a rapid performance check

    [606kB]
  • (AP101) Machine condition monitoring - multi-axis (AP101) Machine condition monitoring - multi-axis [en]

    Productive Process Pattern™ from the foundation layer of the Productive Process Pyramid™. Use a workpiece inspection probe, which is often already fitted to complex machines, together with an AxiSet™ Check-Up system. In just a few minutes, users can identify and report on poor machine rotary axis alignments and, if ne

    [790kB]
  • (AP200) Part identification (AP200) Part identification [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a workpiece inspection probe to take measurements on the raw material (or previously machined features) to determine the identity of the component, the component alignment on the machine tool, and/or to check for non-con

    [853kB]
  • (AP201) Intelligent program selection (AP201) Intelligent program selection [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a workpiece inspection probe to determine whether the component blank loaded in the machine tool is the correct one for the machining program. Where a unique, identifiable feature exists on the component (or one can be

    [697kB]
  • (AP202) Part presence check (AP202) Part presence check [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a workpiece inspection probe to identify which components are actually present and should be machined. The probing results can be used to control program logic that determines whether to machine a component or to skip m

    [383kB]
  • (AP203) Job set-up (AP203) Job set-up [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a workpiece inspection probe to automatically measure the location of the component and update the relevant offset. Where appropriate, also use the probe to update the orientation of the component using a controller func

    [393kB]
  • (AP204) Productive Process Pattern: Tool setting (AP204) Productive Process Pattern: Tool setting [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a tool setting probe mounted within the machine tool to automatically set the length and diameter of each tool before machining begins.

    [654kB]
  • (AP205) Productive Process Pattern: Tool identification (AP205) Productive Process Pattern: Tool identification [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. An on-machine tool setting system is used to establish tool length and diameter offsets when replacing tools. As a safety check, the measured values are compared against reference dimensions with a tolerance applied: if the

    [1,3MB]
  • (AP206) Machine capability check (AP206) Machine capability check [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a workpiece inspection probe to perform a machine capability test before machining. Commence machining only if the machine is within the capability limits defined for the component. Measuring known reference features s

    [699kB]
  • (AP207) Clearance check (AP207) Clearance check [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a workpiece inspection probe to test critical sections of a toolpath where interference is possible. The probe will stop when a collision is detected making it safe to perform this check: a cutting tool is not able to pr

    [690kB]
  • (AP208) Parametric programming (AP208) Parametric programming [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a workpiece inspection probe to measure features which vary between parts within a given family and allocate macro variables for those feature measurements. Different parts can be produced by a family-specific rather tha

    [892kB]
  • (AP209) Path optimisation (AP209) Path optimisation [en]

    Productive Process Pattern™ from the process setting layer of the Productive Process Pyramid™. Use a workpiece inspection probe to measure workpiece condition. Apply logic based on the measured stock size to control the cutting path so that air cutting is eliminated and machining moves always cut metal.

    [819kB]
  • (AP210) Adaptive machining (AP210) Adaptive machining [en]

    A manufacturing process may dictate that the form of a finished component is dependent on the form of the input material for that process. In these circumstances, it is necessary to measure the form of the input component and use the measurement to produce a customised cutting program which is unique to that component

    [799kB]
  • (AP301) Cutter parameter update (AP301) Cutter parameter update [en]

    Productive Process Pattern™ from the in-process control layer of the Productive Process Pyramid™. Use a workpiece inspection probe to measure the actual size of a machined feature and update the relevant tool offset.

    [485kB]
  • (AP302 addendum) Productive Process Pattern: Three pillar test piece: an example of dynamic re-machining (AP302 addendum) Productive Process Pattern: Three pillar test piece: an example of dynamic re-machining [en]

    Explanation of machining processes and strategies used to produce the three pillar test piece, and aid in demonstrating the benefits of in-process control.

    [346kB]
  • (AP302) Productive Process Pattern: Dynamic re-machining (AP302) Productive Process Pattern: Dynamic re-machining [en]

    Productive Process Pattern™ from the in-process control layer of the Productive Process Pyramid™. The CNC machining process uses semi-finishing cuts or test cuts (slave features) that are representative of the subsequent finishing cut. The probing system on the machine is used to measure the cut feature and adjust the

    [810kB]
  • (AP303) Productive Process Pattern: Thermal correction - machine drift (AP303) Productive Process Pattern: Thermal correction - machine drift [en]

    Productive Process Pattern™ from the in-process control layer of the Productive Process Pyramid™. Use a workpiece inspection probe to locate and measure the position of a critical reference feature in order to detect machine drift, or use an on-machine tool setter to track movement in a machine’s Z-axis caused by ther

    [1,0MB]
  • (AP304) Productive Process Pattern: Tool condition monitoring (AP304) Productive Process Pattern: Tool condition monitoring [en]

    Productive Process Pattern™ from the in-process control layer of the Productive Process Pyramid™. When tool breakage is identified as a significant expected risk, it is useful to monitor the condition of the cutting tools which are being used. Performing a tool breakage check immediately after using a tool can help

    [187kB]
  • (AP305) In-process datum setting (AP305) In-process datum setting [en]

    Productive Process Pattern™ from the in-process control layer of the Productive Process Pyramid™. Use a workpiece inspection probe to measure datum features then store feature or part locations in the CNC in order to reset a current work coordinate system (WCS), or define a new WCS automatically. This procedure can be

    [261kB]
  • (AP306) Productive Process Pattern: Thermal correction - workpiece expansion (AP306) Productive Process Pattern: Thermal correction - workpiece expansion [en]

    Productive Process Pattern™ from the in-process control layer of the Productive Process Pyramid™. Use a spindle probe to measure the size of a reference feature in the machine environment and compare it with the known size of that feature at 20 °C. Produce and apply a scaling factor or offsets to subsequent part meas

    [1,0MB]
  • (AP400) Process reporting (AP400) Process reporting [en]

    Productive Process Pattern™ from the post-process monitoring layer of the Productive Process Pyramid™. Most CNC control systems have the capability to send customised information through RS232 serial ports, an Ethernet connection, or to the hard disc of the CNC control. The reporting capability allows a traceable rec

    [280kB]
  • (AP403) Critical feature reporting (AP403) Critical feature reporting [en]

    Productive Process Pattern™ from the post-process monitoring layer of the Productive Process Pyramid™. Select the critical features which are to be measured and reported, according to a set of criteria. Features should be reported where the failure of a feature would be indicative of a more serious process fault (e.g.

    [741kB]